SEACON 2008 - SEACON

SEACON’s US Gulf Area Sales Move to New Premises

29/6/08.

Effective January 1, 2009:

SEACON US Gulf Area Sales Office will be operating from new premises. All inquiries should continue to be directed through Glenn Pollock who can be reached on the original contact telephone and fax numbers.
Phone: +1 (281) 599-3509
Fax: +1 (281) 599-3517

In addition to the new contact address, details below:

SEACON US Gulf Area Sales Office
21925 Franz Road, Suite 401
Katy, TX 77449, USA

E-mail: gulf@seaconbrantner.com
Website: www.seacon-usa.com

 

Another Successful OTC for the SEACON Group

29/6/08.

OTC 2008 held between 5th – 8th May at the Reliant Center in Houston, Texas was once again a very successful exhibition for the SEACON Group with many visits to our booth from both new and existing customers and many new leads generated. In addition, this exhibition saw a number of new products being displayed by the Group including the GLOBE-CON and CS-MSAJ dry-mate connector series along with SEACON’s vast fiber optic range and many new products built for specific customer requirements. For further information on new product developments please contact SEACON on +1-619-562-7071

WET-CON, Micro WET-CON and Micro WET-CON Split Series Connector Enhancements

25/6/08.

WET-CON, Micro WET-CON and Micro WET-CON Split Series Connector Enhancements

As part of our continuous improvement process the SEACON Group consistently reviews it’s product ranges through both customer feedback and internal improvements.  It is via these processes that SEACON identified a design enhancement to the WET-CON and Micro WET-CON connector ranges.  This new design improvement has now been implemented not only across these two connector ranges, but also the new Micro WET-CON Split Series.

The design change is associated with the Male Pin connectors only and has been introduced to improve and extend the life of the connectors by decreasing the stresses that are applied to the sealing interface between the male contact pin and the sealing rubber around the pin during the connectors mate and de-mate cycles.

The newly designed male contact has a “Lead in” as part of the contact pin itself which replaces the current rubber lead in. The introduction of the new pin removes any potential wear to the sealing interface between the male contact pin and the sealing rubber around the pin which may occur with many repeated make and breaks of the connector pairs. The new pin will maintain the full connector sealing properties and will provide a greater life expectancy of the connectors.

The incorporation of this design change to the Male Pin connectors will not affect the existing Female Socket connectors currently being used by SEACON’s customers and therefore full intermateability will be maintained. In addition, SEACON would also like to confirm that pricing will also not be affected.

This new pin design concept has been fully tested and has been utilized in both the U-MATE and SEA-MATE connector ranges for a number of years.

For further information please contact SEACON Global Production at sales@seaconglobal.com or SEACON (europe) Ltd at sales@seaconeurope.com

New CS-MS Dry-Mate Connector Series

23/6/08.

New CS-MS Dry-Mate Connector Series

The SEACON Group is pleased to introduce a new range of underwater electrical dry-mate connectors.

Originally developed in conjunction with C.R. Encapsulation to meet the needs of ROV manufacturers and their equipment suppliers, the CS-MS series offers a standard aluminum shell with dual o’rings and is designed to accommodate a standard oil-filled hose.

Currently available in 2 shell sizes with 3 to 10 contact configurations as well as a single channel fiber optic version, this high specification and high integrity connector fits industry standard bulkhead interfaces and is available in alternative materials including Stainless Steel and Titanium and can be molded to many standard cables.

Pressure rated to 10,000 psi, this new series is also suitable for a variety of other applications including underwater cameras and lights, diver communications, recreational submersibles, towed array cable systems, current meters, animal migration research and food processing equipment.

For further information please view our website at www.seacon-usa.com or e-mail sales@seaconglobal.com

For details on our single-channel fiber optic version please email sales@seacon-ap.com

GLOBE-CON: New Connector Developments

22/6/08.

Several new connector developments have taken place this year within the SEACON Group.


The first of which is the release of the GLOBE-CON connector range that was developed for a European customer involved in a major offshore development project. Small in diameter this connector series is manufactured using Viton and is capable of withstanding temperatures of up to 150 degrees Fahrenheit. Available in three shell sizes with up to 12 contacts and rated to 10,000 psi (22,500ft / 7,000m), this connector range is particularly sturdy and robust, coupled with it’s high temperature rating, makes the GLOBE-CON suitable for many harsh environment applications.

Range of split connectors added to the Micro WET-CON series

2/6/08.

SEACON has now added a range of split connectors to it’s popular Micro WET-CON wet mateable series. This series of connectors was originally developed to provide all the features of the ALL-WET connector range, but in a miniature industry standard configuration. The introduction of the new split connectors to the Micro WET-CON range will prevent costly ‘Y’ assemblies and will allow ease of replacement of break-outs by the customer. This smaller connector series offers the same flexibility and reliability as SEACON’s standard rubber molded connectors, in a lightweight and user-friendly model.

Please contact SEACON Global for further information on sales@seaconglobal.com

Sea Technology Magazine – May 2008 – SEACON Technology Crucial For Antarctic Research

25/5/08.

Sea Technology Magazine – May 2008 – SEA CON Technology Crucial For Antarctic Research

An ambitious scientific research project at the South Pole, appropriately called IceCube, has brought together academia and industry to study elusive subatomic particles from space. IceCube involves sinking an array of sensors into the Antarctic ice cap to form a one-cubic-kilometer telescope looking toward the center of the Earth. SEACON Brantner & Associates Inc. (El Cajon, California) is one of the project’s partners, providing the connectors and cable terminations for IceCube.

The company overcame a number of special challenges to ensure that its technology, originally designed to operate in the ocean, could deliver the performance required in the low temperature and high hydrostatic pressure of one of the harshest possible operating scenarios—being permanently encased in ice more than one mile beneath the Antarctic ice cap.

Why Study Neutrinos?
The goal of the IceCube experiment is to detect high-energy neutrinos. Neutrinos are tiny, point-like particles that have no electric charge, nor do they readily interact with matter. There might be 10 trillion neutrinos passing through the human body every second, but a person is unlikely to have even a single neutrino interact inside the body during a lifetime. This property makes neutrinos useful to astronomers who wish to understand the physics of the highest energy sources of radiation in the universe. It also means that neutrinos can be observed only through a very large detector. IceCube encompasses one billion tons of ice, but scientists expect to capture only a handful of neutrinos every year. The neutrinos interact in the ice and then become particles called electrons and muons, which give off a bluish light—the optical counterpart of a sonic boom—which is detected by the IceCube sensors.

Background and Project History
In 1993 and 1994, several astrophysicists at the University of California, Berkeley; the University of California, Irvine; and the University of Wisconsin (UW), Madison, sank photo tubes to a depth of one kilometer in the Antarctic ice to study neutrinos in a project called Antarctic Muon and Neutrino Detector Array (AMANDA)— funded by the National Science Foundation (NSF) and other governments and organizations internationally.

Between November 1996 and February 1997, 216 of the 330-millimeter-diameter digital optical modules (DOMs), containing photodetectors, were placed in six holes at a depth of two kilometers, with 36 DOMs per string. Scientists increased the earlier one-kilometer sampling depth to 1.5 to two kilometers, which improved results because bubbles that scatter light were not as prevalent below 1.5 kilometers. This effort was called AMANDA B, and the original project was retroactively referred to as AMANDA A.

Between 1997 and 2004, the AMANDA B project continued its neutrino research at the South Pole scientific station. The AMANDA telescope, still in place and functioning today, amounted to the proof of concept for the feasibility of IceCube. AMANDA covered a volume of 0.02 cubic kilometers.

In 2004, NSF awarded a multiyear contract to the Antarctic Astronomy and Astrophysics Institute at UW Madison to manage the IceCube project. In addition to its earlier participation in the AMANDA A and B projects, in which it drilled 19 holes at depths of up to two kilometers and deployed more than 600 optical sensors, UW Madison had established credentials for electrical and electronics engineering, astrophysics and related technical expertise. The first sensor string was drilled and deployed at the South Pole Station in January 2005, and the sensor array is due for completion in 2011.

The telescope is located at the South Pole, since the ice, formed by the compression of incremental snow over thousands of years, is about as pure as any ice on Earth below the depth of 1.45 kilometers. In addition, at -50° C, South Pole ice is nearly the coldest on
the planet, causing far less thermal noise than ice in warmer temperatures. The first 50 meters of subsurface material is snow, followed by ice extending to a depth of one kilometer beneath the surface. In comparison, while there is a one-kilometer vertical separation (i.e., from 1.4 to 2.4 kilometers) between the top of the sensor string and the bottom, the Eiffel Tower is only 300 meters tall.

Why SEACON Connectors?
UW Madison evaluated several manufacturers before selecting SEACON as the IceCube connector manufacturer in 2004. SEACON brings 40 years of connector experience to the project, along with a history of participating in AMANDA A and B.

In addition, SEACON offered several advantages. The company had a record of meeting demanding delivery schedules, a large selection of specialty connectors and a commitment to continuously improve the cable system and manufacturing processes, an open-door policy to customers and a staff of highly experienced employees, including production manager and IceCube project manager Kry Leap, who has more than 30 years of experience in the underwater connector industry. Most importantly, the company had experience in areas necessary to the project, such as assembly manufacture, including mating a penetrator assembly to a power/communications cable, which is the link between the sensor string and the outside world; overmolding, a method to create a seal between the cable and connector body; and cable breakouts, which are a method of reinstating a cable jacket following damage to or an intentional breach of the jacket.

IceCube System Details
When completed, the IceCube string configuration’s 4,800 InIce DOMs will have 17 vertical meters of separation between each two sensors on a given string.

There will be up to 80 strings, each string separated by 125 meters from its nearest neighbor. The strings are installed by drilling holes in the ice, using an enhanced hot water drill. When finished, the hole is approximately 2,500 meters deep and 60 centimeters in diameter.

Once the hole is ready, installers have approximately 24 hours to connect the DOMs to the surface-to-DOM cable and suspend them in position. A five-meter-tall tower positions the cable over the hole and allows the installers to attach the DOMs to the surface-to-DOM cable. The cable is then lowered until a DOM connection point, consisting of two Yale Cordage (Saco, Maine) YalegripsTM attached to the cable, is reached. Then the steel cables of the DOM harness are attached to the cable Yalegrips. The DOM penetrator assembly connectors are also mated to the SEA CON XSJJ connectors of the cable.

Once the string has been lowered into its final position, the string is left to freeze in place, and the IceCube sensors are ready to begin taking data. A DOM senses photons through its photomultiplier tube (PMT), and PMT data is digitized by the DOM electronics.

This digital data is sent up through the SEACON-manufactured DOM penetrator assembly, protected by aTeledyne Benthos (North Falmouth, Massachusetts) pressure sphere, and through a SEACON glass-reinforced epoxy (GRE) XSJJ connection to the surface-to-DOM cable.

This cable, manufactured by Ericsson Network Technologies (Hudiksvall, Sweden), is 2,505 meters long and is comprised of 20 quads of conductors of nominally 145 ohms impedance. It has Kevlar outer and central-strength members, providing 55 kilonewtons of mechanical reinforcement. Waterblocking around the quads prevents any water or ice from damaging the symmetry of the cable. A copper shield is used to provide electrical noise isolation.

The XSJJ connection is made possible by the SEACON breakout design. Breakouts are installed by slicing open the cable, cutting the correct quads, terminating them to the XSJJ connectors, waterproofing and overmolding the connectors and then resealing the cable. Once data from the DOM is inside the surface-to-DOM cable, it travels up to the ice surface and on to the IceCube surface cable via militaryspecified (MS) round, metal shell connectors installed by SEACON.

The surface and surface-to-DOM cables are mated in a stainless steel junction box. IceTop sensors are brought into the IceCube cable system via the surface junction box. The surface cable is also manufactured by Ericsson Network Technologies and has a similar construction to the surface-to-DOM cable, with the exception of the waterblock and Kevlar strength member. The data continues through the surface cable and into the IceCube Lab (ICL), where it meets another MS connection to short, patch cables, which are assembled by SEA CON. By that time, the data has traveled anywhere from 2,650 to 3,300 meters of cable. The data is acquired in the ICL and transmitted to the IceCube headquarters in Madison, Wisconsin, via satellite at a rate of 30 gigabytes of data per day.

Special Considerations
Operating in the ice shafts imposes extraordinary stress in the form of both temperature and hydrostatic pressure on all elements of the sensor string—cables, connectors, penetrators and the Benthos pressure sphere. The SEACON XSJJCCP7 and XSJJCCR7 connectors, used to mate the long penetrator assembly DOMs in the sensor array, and the XS77CCP9 and XS77CCR9 connectors, used to mate the short penetrator assembly DOMs, are exposed to 6,000 pounds per square inch of pressure in the ice shaft by the time the holes refreeze and encase the strings in new ice.

The challenges to SEACON included working with extremes of temperature, not only the low temperature once the ice had frozen, but also the higher temperature during filling on the drilled hole; working at high pressures resulting from the compression of the ice; developing a reliable, repeatable method to break into a multistranded cable and reinstating the integrity of the cable to a level that can withstand not only the operating environment but also the rigors of deployment; selecting the correct connector, critical due to the permanent installation restriction and no maintenance opportunities once installed; handling multiple 2,500-meter cable lengths to enable accurate and reliable completion of multiple breakouts distributed in close proximity to each other; and project management of a complex set of cable assemblies with critical delivery demands due to logistical constraints in transferring cable to the South Pole. With the extensive range of connectors SEACON has in its portfolio, minimal modifications were required to the connectors selected for the IceCube program; however, developing a reliable cable breakout system for the surface-to-DOM cable benefited from many aspects of SEACON’s 40 years of experience in supplying cables and connectors for underwater, harsh-environment NSF applications. Despite the many challenges, project workers have made steady progress toward having all 80 sensor strings installed by 2011.

Conclusions
Because the South Pole’s extreme temperatures tend to keep frozen objects frozen into the foreseeable future, as well as the fact that the South Pole Station is so far inland, IceCube’s sensor strings will likely be in long-term cold storage for hundreds of years.
IceCube is a tangible illustration of the success of instrumentation functioning unattended in a long-term deployment to gather and transmit valuable data from one of the harshest operating environments on Earth.

SEACON’s expertise in cable termination, overmolding and connector technology has enabled sensor strings to perform well, despite the project’s demands that components work together in a location decidedly outside their intended operational setting. IceCube is a dramatic example of productive collaboration between industry and the scientific community to reach a mutual goal. Providing accessibility to the customer—maintaining real-time communications and jointly solving operational issues as they emerge—tran-scends the IceCube project and tends to lead to successful outcomes, regardless of the application.

Acknowledgments
This material is based upon work supported by NSF under Grant Nos. OPP-9980474 (AMANDA) and OPP-0236449 (IceCube), UW Madison. The $272 million project, managed by UW Madison, is funded by NSF, which is currently contributing $242 million, and other scientific organizations from five countries.